Evolve Tools

Minimum order quantity: 10 Piece

We are well-known firm of 16mm Inside Grooving Tool. In addition, quality experts also check the quality of this product on varied industry standards. Besides, we offer this product at nominal costs.





ID Grooving - Taegutec Insert

Minimum order quantity: 10 Piece

The series number is the opening diameter of the tapered receptacle, in millimetres. ER collets collapse to hold parts up to 1 mm smaller than the nominal collet internal size in most of the series (up to 2 mm smaller in ER-50, and 0.5 mm in smaller sizes) and are available in 1 mm or 0.5 mm steps

Minimum order quantity: 10 Piece

The CNC grooving tool is built differently for face and radial grooving. In a radial grooving holder the support section under the insert is straight, while in a face grooving holder it is curved.

Minimum order quantity: 10 Piece

Our ER collet chucks are ideal for holding workpieces securely in place making them handy for milling. Available in a range of sizes to suit your needs.Collets are used to hold a tool in a central position as it rotates. As the tool is inserted into the collet, the device expands and provides uniform pressure that holds the tool in place. However, if the collet stretches too far, it cannot secure the instrument properly and may lose shape.

Minimum order quantity: 10 Piece

The screw holds the positive type insert rigidly in place for stability during operations. The inserts can be easily and rapidly replaced once worn down thus saving machining time and cost.

Minimum order quantity: 10 Piece

ID Grooving Boring Bars - Korloy Insert

Minimum order quantity: 10 Piece

Parting uses a blade-like cutting tool plunged directly into the workpiece to cut off the workpiece at a specific length. It is normally used to remove the finished end of a workpiece from the bar stock that is clamped in the chuck


TOOLS SIZE

• TTER/L25252T12
• TTER/L25252T15
• TTER/L25252T20
• TTER/L25252T25

Minimum order quantity: 10 Piece

Material. Steel,Brass ; Usage/Application. Use in CNC and Milling Machine 

Properties and application:

• External turning toolholder
• Clamping system: S
• Insert type: VB.T 1604..
• Clearance angle: 93°
• Hardened and tempered shank up to 40 - 45HRC
• Set contains clamping screw and wrench

Minimum order quantity: 10 Piece

Boring bars are single-point tools used in metalworking for straightening and finishing drilled or cast holes using interchangeable carbide inserts. A lathe or a turning machine attaches them to the workpiece as it turns against the boring bar's cutting tip.

Minimum order quantity: 10 Piece

The BTUNR/L Boring Bar is made from a high quality Steel shank and is suitable for use with TN** style turning inserts. These turning tools have a Double Clamp ...

Properties and application:

• Internal boring bar
• Clamping system: B
• Insert type: TN.. 1604..
• Clearance angle: 93°
• Hardened and tempered shank up to 40 - 45HRC
• Set contains clamping screw and wrench

Minimum order quantity: 10 Piece

U drills are a kind of drilling instrument that include carbide inserts. These inserts are easy to replace and cost effectively. Insert type U-drills are used for the process of embedding heat pipe because of their widespread employment in CNC machining centers and high-speed machining applications.

Minimum order quantity: 10 Piece

BCLNR 2525 M12-APT Turning Tool 25x25mm shank 32mm qualified width 150mm long right hand uses CNMG 1204 Inserts. 95° Turning and facing using CNMG 1204-- inserts. * The qualified width is the distance from the back of the tool to the cutting tip of the insert.

TOOLS SIZE:-

• BCLNR/L2020K12
• BCLNR/L2525M12
• BCLNR/L3232P12
• ACKNR/L2020K12
• ACBNR/L2020K12
• ACKNR/L2525M12
• ACBNR/L2525M12

Minimum order quantity: 10 Piece

Top clamp style holders utilize a clamp to securely hold top clamp inserts via a groove on top of the insert. Top clamp inserts use a good amount of carbide and carbide shims, and can sometimes be provided on the insert holder, offering a strong and stable system for threading.

Minimum order quantity: 10 Piece

Parting uses a blade-like cutting tool plunged directly into the workpiece to cut off the workpiece at a specific length. It is normally used to remove the finished end of a workpiece from the bar stock that is clamped in the chuck

TOOLS SIZE

• TTER10102T18
• TTER/L16162T15
• TTER/L16162T20
• TTER/L20202T15
• TTER/L20202T20
• TTER/L25252T15
• TTER/L25252T20
• TTER/L25252T25

Minimum order quantity: 10 Piece

VNMG type holders are for profile turning and finish turning applications. It is best for machining shaft type components.

• Screw type boring bars and 95° approach angle for negative 35° Rhombic inserts

• SVJNL 2020 M16
• SVJNR 2020 M16
• VJNL 2525 M16
• SVJNR 2525 M16
• SVQNL 2525 M16
• SVQNR 2525 M16

Minimum order quantity: 10 Piece

The BVJNR/L Turning tool Holder is suitable for use with VN** style turning inserts. These turning tools have a TOP Clamp style clamping system with a 93 degree approach. Teknik tool holders offer excellent precision and value. Constructed from a high grade tool steel for the highest accuracy, rigidity and best performance turning. Available in right or left hand types.Properties and application:

• External turning toolholder
• Clamping system: b
• Insert type: VNMG 1604..
• Clearance angle: 93°
• Hardened and tempered shank up to 40 - 45HRC
• Set contains clamping screw and wrench

Minimum order quantity: 10 Piece

Properties and application:

• External turning toolholder
• Clamping system: B
• Insert type: TN..1604..
• Clearance angle: 93°
• Hardened and tempered shank up to 38 - 42HRC
• Set contains clamping screw, shim and wrench

• Cutting direction: right;
• Length: 125 mm;
• Clearance angle: 93°;
• Cutting edge length: 16 mm;
• Insert: TN.. 1604..

Minimum order quantity: 10 Piece

Properties and application:

• External turning toolholder
• Clamping system: B
• Insert type: TN.. 1604..
• Clearance angle: 60°
• Hardened and tempered shank up to 40 - 45HRC

Minimum order quantity: 10 Piece

Properties and application:

• External turning toolholder
• Clamping system: S
• Insert type: VB.T 1604..
• Clearance angle: 72,5°
• Hardened and tempered shank up to 40 - 45HRC
• Set contains clamping screw and wrench

Minimum order quantity: 10 Piece

Parting is a machining operation that results in a part cut-off at the end of the machining cycle. The process uses a tool with a specific shape to enter the workpiece perpendicular to the rotating axis and make a progressive cut while the workpiece rotates.

Tools Size

• TTER/L20202T15
• TTER/L20202T20
• TTER/L20203T12
• TTER/L20203T15
• TTER/L20203T20
• TTER/L20203T25
• TTER/L20204T15
• TTER/L 20204T20

Minimum order quantity: 10 Piece

The BWLNR/L Turning tool Holder is suitable for use with WN** style turning inserts. These turning tools have a Multi Lock style clamping system with a 95 degree approach.

TOOLS HOLDER SIZE

• BWLNL 2020 M08
• BWLNR 2020 M08
• BWLNL 2525 M08
• BWLNR 2525 M08
• BWLNL 3232 M08
• BWLNR 3232 M08

• External turning toolholder
• Clamping system: B
• Insert type: WN..0804..
• Clearance angle: 95°
• Hardened and tempered shank up to 40 - 45HRC

Minimum order quantity: 10 Piece

The BTJNR/L Turning tool Holder is suitable for use with TN** style turning inserts. These turning tools have a Multi Lock style clamping system with a 93 degree approach. Teknik tool holders offer excellent precision and value.

External Turning Toolholder

• Clamping system: B
• Insert type: TN..1604..
• Clearance angle: 93° 
• Hardened and tempered shank up to 40 - 45HRC

1. BTJNL2020M16
2. BTJNR2020M16
3. BTJNL2525M16
4. BTJNT2525M16
5. BTJNL3232P16
6. BTJNT3232P16

Minimum order quantity: 10 Piece

Brico tools one piece clamp type Parting & Grooving Tool Holders

Suitable for external grooving, parting, turning, relieving, profiling.

TOOLS SIZE
MGEHR/L20202T15
MGEHR/L20202T20
MGEHR/L25252T12
MGEHR/L25252T15
MGEHR/L25252T20
MGEHR/L25252T25

Minimum order quantity: 10 Piece

HYDRO-GRIP has a very compact and tough design. Tool changes are made quickly, easily and with high levels of precision. The high clamping force guarantees a secure clamping of your milling, drilling and reaming tools.

Minimum order quantity: 10 Piece

BT40 APU Drill Chuck is manufactured in a one-piece design with precision grounded surfaces. This keyless drill chuck with integrated BT40 shank is highly suitable for CNC drilling and cutting works in industries.

ISO30 APU Drill Chuck is manufactured in a one-piece design with precision grounded surfaces. This keyless drill chuck with integrated ISO30 shank is highly suitable for CNC drilling and cutting works in industries.

Minimum order quantity: 10 Set

Soft Jaws are used to clamp pre-machined component for further machining to desired accuracy especially on CNC Lathe. These are made of mild steel or En24, En36, & En8 to ensure its long work performance. Soft jaws simplifying the task of jaw placement on three jaw chuck.

Minimum order quantity: 10 Piece

Minimum order quantity: 10 Piece

Side lock holders also known as Drill Holders are used to hold indexable type drills – Cylindrical shanks with parallel flats (ISO9766) with great rigidity and accuracy.

Stub Milling Arbors are used for holding saws or small cutters. These are specially designed and made to fit directly into standard end mills adapters. It is suitable for conventional milling as well as climbing milling.

Minimum order quantity: 100 Piece

Minimum order quantity: 10 Piece

E Clamp Tool Holder ; Material, Hard Alloy ; Holding Capacity, 32mm ; Surface Finish, Polished ; Usage/Application, CNC Machines ; Product Type, Turning Tool.

Minimum order quantity: 1 Piece

• collections/sleeves
• Manufactures from selected high-grade carbon steel. We put full efforts into providing you world-class tooling.
• Universal Model Turrent Sleeve is suitable for any make of Turrent.
• Suitable to hold Cylindrical Shank Tools on Turret of CNC sleeve.

Minimum order quantity: 10 Piece

The standard ER collet is the most widely used clamping system in the world. Made from Alloy spring steel and fully hardened these ER collets are ideal for many machining applications including boring, milling, reaming, tapping and grinding.